TM 1-1510-225-10 3D-14 pressed,   that   waypoint   identifier   will   display   on   the Direct To page. (2)   If  the  KLN  90B  is  displaying  the  Super NAV 5   page  and  the  right  inner  knob  is  in  the  out position,  the  waypoint  highlighted  in  the  lower  right hand  corner  of  the  Super  NAV  5  display  will  be  the default waypoint. If condition number 1 or 2 isn’t occurring: (3)   If  there  is  any  waypoint  page  (APT  1-8, VOR,  NDB,  INT,  SUP,  or  ACT  page)  in  view  on  the right  side  when  the      D   button is pressed,  the Direct To page will contain the identifier of the waypoint being viewed on the right side. If  none  of  conditions  number  1,  number  2,  or number 3 above are occurring, then: (4)   When   the      D         button   is   pressed,   the waypoint  identifier  for  the  current  active  waypoint  will be  displayed.    However,  if  the  active  waypoint  is  the missed  approach  point  and  the  aircraft  is  passed  the missed  approach  point,  the  KLN  90B  will  display the first  waypoint  of  the  missed  approach  procedure  on the Direct To page. (5)   If  there  is  no  active  waypoint  when  the    D      button  is  pressed,  the  Direct  To  page  displays blanks.  In order for there not to be an active waypoint, there   is   no   direct   to   waypoint   and   there   are   no waypoints in flight plan 0. b.  Direct To – Procedure 1. 1.   Press the  D    button.  The Direct To page is  displayed  on  the  left  side.    The  cursor will   already   be   on   the   left   page.      A waypoint   identifier   may   or   may   not   be displayed. 2.   Rotate the left inner knob to select the first character of the desired waypoint’s identifier. 3.   Rotate    the    left    outer    knob    one    step clockwise  to  move  the  flashing  portion  of the    cursor    over    the    second    character position. 4.   Rotate   the   left   inner   knob   to   select   the second character of the identifier. 5.   Use  the  left  outer  and  inner  knobs  as  in the   previous   steps   until   the   desired   is completely displayed. 6.   Press    the    ENT    button    to    display    the waypoint  page  on  the  right  side  for  the selected waypoint.  If an incorrect identifier has been entered, immediately start using the  left  inner  knob  to  re-enter  the  correct identifier. 7.   Press the   ENT  button  again  to  approve the  displayed  waypoint  page.    The  right side  will  display  the  NAV  1  page,  Figure 3D-9,  and  the  left  side  will  return to page that  was  displayed  prior  to  pressing  the   D        button.    If  the  direct  to  was  started while  the  NAV  1  page  was  shown  on  the left side, the left and right pages will revert to  the  pages  that  were  shown  before  the direct    to    was    started.        The    selected waypoint    is    now    the    active    direct    to waypoint.     D KOSH DIS   683NM GS    193KT ETE    3:34 BRG    303^o NAV 1 +    +    +    +    +        +    +    +    +    + Figure 3D-9.  NAV 1 Page (Direct To Operation) NOTE In some cases during approach operations, the KLN 90B presents a page asking how a waypoint     is     used     when     the     waypoint identifier is entered character by character.   When     this     page     is     presented,     simply choose   the   desired   use   of   the   waypoint (e.g.,  FAF  or  MAHP)  by  moving  the  cursor with the left outer knob and pressing ENT.   Choosing  correct  use  of  the  waypoint  is required to ensure proper waypoint sequencing  once  the   aircraft  reaches  the waypoint. c.   Direct To – Procedure 2. 1.   Select  the  desired  waypoint  page  on  the right side.