TM 1-1510-218-10 3-38 Pulling the knob back out will allow further scanning of the waypoint pages in the active flight plan. aj.    Direct  To  Operation  On  The  Active  Flight Plan.  When  DIRECT  TO  operation  to  a  waypoint  on the   active   flight   plan   is   selected,   the   system   will provide navigation to the waypoint and then automatically  resume  navigation  along  the  flight  plan when the DIRECT TO  waypoint is reached.   Waypoints that exist prior to the DIRECT TO  waypoint in  the  active  flight  plan  are  bypassed.    Navigation  on the active flight plan will not be resumed if the  DIRECT TO operation is to a waypoint that is not in the active flight plan. Any   of   the   methods   previously   described   for initiating   DIRECT   TO  operation  may  be  used.    The following procedure is the easiest for this application. 1.   Select the FPL 0 page on the left side. 2.   Press the left  CRSR button and then use the  left  outer  knob  to  position  the  cursor over the desired waypoint.  Refer to Figure 3-45. 3.   Press  the      D        button.    The  waypoint page   for   the   selected   waypoint   will   be displayed   on   the   right   side.      Refer   to Figure 3-46. 4.   Press    the    ENT    button    to    approve    the waypoint page.  The  DIRECT TO waypoint identifier  in  the  active  flight  plan  will  now be   preceded   by   an   arrow,   Figure   3-47.   The      symbol is not displayed since there is no FROM waypoint. ACT   2 GPT D V GULFPORT       L 109.00  2^o E N 30^o 24.40’ W 89^o 04.60’ E N R   -   L E G   1:KNEW   2:GPT   3:SJI   4:CEW   5:MAI   8:KPIE CRSR Figure 3-45.  Select the DIRECT–TO Waypoint DIRECT TO:   SJI VOR SJI D SEMMES       H 115.30  5^o E N 30^o 43.55’ W 88^o 21.56’ E N R   -   L E G E N T CRSR Figure 3-46.  DIRECT–TO Waypoint NAV 1 E N R  -  L E G   1:KNEW   2:GPT   3:SJI   4:CEW   5:MAI   8:KPIE FPL 0     D SJI DIS  90.4NM GS    180KT ETE     :30 BRG    062^o +    +    +    +    +        +    +    +    +    + Figure 3-47.  DIRECT–TO Navigation An alternative method is to use the Super NAV 5 page to select the direct to waypoint.  Pull out on the right inner knob.  With the inner knob out, it is possible to scan through the waypoints of the active flight plan.   When  the  desired  waypoint  is  highlighted,  press  the    D    button and then the ENT button. To    cancel DIRECT     TO     operation     prior     to reaching the  DIRECT TO waypoint in order to proceed along the flight plan leg, press the    D        button, then press the CLR button and then press the  ENT button. ak.  Distance/Time   Pages.       The    distance/time pages  are  designed  to  be  used  with  the  active  flight plan. (1)   Distance/Time  1  Page.  When the FPL 0 page  is  displayed  on  the  left  side  and  the  D/T  1  page is   displayed    on    the    right    side,    the    distance    and estimated  time  en  route  are  displayed  for  each  of  the active flight plan waypoints.  The distance displayed is the   cumulative   distance   from   the   aircraft's   present position  to  each  waypoint  along  the  flight  plan   route.   The ETE is displayed in hours and minutes.  Refer to Figure 3-48.  If  DIRECT TO operation is occurring to a waypoint that is not in the active flight plan, the D/T 1 page is blank when the FPL 0 page is displayed on the left.