TM 1-1510-225-10 3D-54 2.   Turn  the  right  cursor  on  by  pressing  the right  CRSR button.   Rotate the right outer knob  until  the  cursor  is  over  the  desired SID.  Press the ENT button. 3.   The  KLN  90B  will  ask  for  the  runway  in use.          Position     the     cursor     over     the appropriate   runway   and   press   the   ENT button. 4.   The transitions are presented for selection.        Move    the    cursor    over    the desired    transition    and    press    the    ENT button. 5.   The KLN 90B presents a list of waypoints that    make    up    the    SID.        Review    the waypoints and press the  ENT button, with the cursor over LOAD IN FPL, to load the SID into the active flight plan. 6.   The KLN 90B will add the SID procedure after   the   airport   reference   point   in   the active  flight  plan.    If  the  airport  reference point   is   not   included   in   the   active   flight plan,   the   KLN   90B   will   ask   to   add   this waypoint to the active flight plan. b.  Selecting a STAR.  Selecting a STAR is very similar to selecting a SID.  The only difference is the order  of  the  steps  to  define  the  STAR  and  where  the STAR is loaded into the flight plan. 1.   Select  the  APT  7  or  the  ACT  7  page  for the  destination  airport.    Ensure the words SELECT STAR are displayed near the top of the screen. 2.   Turn  the  right  cursor  on  by  pressing  the right    CRSR   button,   and,   if   necessary, rotate    the    right    outer    knob    until    the flashing cursor is over the desired STAR.   Press the ENT button. 3.   The  KLN  90B  will  ask  which  transition  to use. 4.   In    some    cases,    the    STAR    procedure requires the selection of a specific runway.   To   select   a   specific   runway,   move   the cursor over the desired runway and press the ENT button. 5.   The KLN 90B presents a list of waypoints that   make   up   the   STAR.      Review   the waypoints and, with the cursor over LOAD IN FPL, press the   ENT button to load the STAR into the active flight plan. The   KLN   90B   will   add   the   STAR   procedure before  the  airport  reference  point  in  the  active  flight plan.    If  the  airport  reference  point  is  not  included  in the active flight plan, the KLN 90B will ask to add this waypoint to the active flight plan. NOTE It  is  not  possible  to  load  a  SID  or  a  STAR into a flight plan other then FPL 0.  SID and STAR  procedures  are  deleted  from  FPL  0 after    the    power    is    off    for    more    than 5 minutes.  c.   Editing  a  SID  or  a  STAR.    SID  and  STAR procedures have procedure headers.  It is possible to use     these     headers     to     delete     and     change     the procedure,   as   is   done   with   approach   procedures.   Refer   to   Figure   3D-73.      Unlike   approaches,   it   is possible to add and delete waypoints in SID and STAR procedures. FPL 0   1:KELP AQN4-STAR   2.INK   3.PHILS   4.TQA 14:KDFW ENR - LEG Figure 3D-73.  SID/STAR Procedure (1)   To help differentiate between approaches (no  adding  or  deleting  waypoints)  and  SID  and  STAR procedures  (adding  and  deleting  waypoints  allowed), the waypoint number is followed by a period (.) next to it    instead    of    a    blank    space.        The    period    also differentiates  a  SID  or  STAR  waypoint  from  a  regular waypoint, which is followed by a colon (:). (2)   Adding an Individual Waypoint in the SID or STAR Procedure. 1.     Use the left knobs to select the FPL 0 page on the left side of the screen. 2.     Turn  the  left  cursor  on  by  pressing the left  CRSR  button.    Rotate  the  left outer  knob  as  necessary  to  position the cursor over the waypoint identifier