TM 1-1510-224-10 (7) Check indications as follows: (a) MFD  INS  BATT,  INS  FAIL,  and WAYPOINT ALERT CWA annunciators (3) illuminated. (b) EHSI    INS    needle    30    degrees right   of   lubber   line   and   course deviation bar displaced right followed  by  INS  needle  centering and course deviation bar displaced  left.    Check  WPT  alert annunciator illuminated. (c) Aircraft caution/advisory annunciator    panel    Amber     INS annunciator light illuminated. (d) INS mode controller Green READY light and red   BATT  light illuminated. (e) Mission  annunciator  panel  Green INS   UPDATE   annunciator    light and    amber    NO    INS    UPDATE annunciator light illuminated. (f) After 15 seconds the text COMPLETE or any active ACTION or MALFUNCTION codes   will   be   displayed.      If   an action   and   malfunction   code   is displayed   they   may   have   been cleared by the BIT test.  The only way    to    ensure    that    they    are cleared is to conduct another  BIT and the text COMPLETE appears. d. ASE    RTU,    2-FM,    3-UHF,    5-UHF,    DTS, MFD   KU,   GPS,    and    ASE    BIT    checks Conduct    as    required    by    depressing    the appropriate line button. «25.  ASE/ACS Program as required. a. Waypoint list Build as follows: (1) Mode   switch   B   Depress   to   select FLIGHT PLAN page. (2) WPT    LIST    (R4)    Depress.        WPT numbers 10-59 are shown.  The  WPT select window surrounds a WPT line. (3) Waypoint  string  (line  number,    WPT ID,     and LAT/LONG coordinates) Enter into scratch pad. (4) ADD/SEL (R1) Depress to load  WPT into system. (5) Or  load  waypoint  list  using  the  data transfer   system   by   depressing   NAV DATA (L2) when the desired data set is   TM   1-1510-224-10   boxed   on   the DATA TRANSFER page. b. Flight plan Build as follows: (1) WPT  numbers  Enter  into  scratchpad in order of desired use (up to nine) or box desired   WPT's and   PREV  (R2) or   NEXT   (R3)   and   depress   LOAD SCRATCH PAD (L5). (2) ROUTES (R5) Depress. (3) Route Select 1st, 2nd, or 3rd to enter WPT    numbers    by    depressing    the appropriate   line   button   to   store   the WPTs. (4) Routes   to   use   as   the   active   FPLN Select  and  depress  the  adjacent  line button to box it. (5) NEW  FPLN  (LI)  Depress  to  activate the FPLN. c. TACAN list Build as follows: (1) Mode   switch   B   Depress   to   select FLIGHT PLAN page. (2) R5  line  selection  switch  Depress  to select TACAN LIST page. (3) TACAN station information (list number, ID, channel number, latitude/ longitude, and station elevation) Enter into scratchpad. (4) R1  line  selection  switch  Depress  to load into system. (5) Or load  TACAN  list  using  the   DATA TRANSFER  SYSTEM  by  depressing NAV     DATA    (L1)     on     the DATA TRANSFER page. (6) TACAN    stations     to     be     used     for updating Select and enter into scratchpad. (7) R4  line  selection  switch  Depress  to select TACAN SELECT. d. Pattern steering mode Program as follows: (1) Mode    switch    B    Depress-to    select FLIGHT PLAN page. (2) R5  line  selection  switch  Depress  to select NAV SETUP page. (3) True bearing Enter into scratchpad. (4) L1   line   selection   switch   Depress   to enter  BEARING. 8-7