TM 55-4820-414-1 3&P FROM P46SR-3 P469R-1 P469R-2 P469R-3 R1-1 R1-2 R1-3 S1-1 S1-2 S1-2 S2-1 32-2 S2-2 S3-2 S3-2 S3-3 S4-2 S4-3 S4-4 FROM XDS4-1 XDS4-2 XDS4-2 XDS5-1 XDS6-2 XDS6-2 XDS6-1 XDS6-2 XDS6-2 XDS2-2 XDSS-2 TB1-1 XDS4-2 XDS6-2 TB1-2 XDS5-2 TB1-5 To — NC TB14 TB1-5 NC A1-E16 A1-E2S A1-E6 TB1-4 TB1-3 S2-2 TB1-7 S1-2 S3-2 S2-2 TB1-9 A1-E62 J3-B J3-F Table 4-5. Test Box Wiring Run List (Cont.) WIRE  NUMBER 36A20 28B20 9H2Q 25A22 23A22 28A22 11E22 11D22 29A22 11D22 11C22 11B22 11C22 30A22 14A22 16A22 15A22 WIRE  NUMBER 21A22 9D22 9E22 27422 9E22 9F22 26A22 9F22 9G22 FROM TB1-4 TB1-6 TB1-5 TB1-6 TB1-6 TB1-6 TB1-7 TB1-7 TB1-8 TB1-S TB1-9 TB1-9 XDS1-1 XDS1-2 XDS1-2 XDS2-1 XDS2-1 XDS2-2 XDS3-2 XDS3-1 XDS3-2 XDS3-2 FROM P4-A16 P4-A1 P4-A2 P4-B7 P4-A14 S4-2 TO — S1-1 P469R-2 XDS6-2 P46SR-2 E2 TB1-8 P46SR-1 S2-1 P466R-2 TB1-6 P466R-1 33-3 W 3 E l XDS3-2 S5-3 Psi-l PS1-2 J3-R XDS1-2 XDS42 WIRE  NUMBER 2SA22 9H20 9G22 9M20 9L22 9J22 29B20 29A22 9K20 9J22 30B20 30A22 11A22 9B22 5A22 5B22 6A22 6B23 9C22 9D22 JUMPER  LIST TO JUMPER  NUMBER P4-B15 1 P4-B1 2 P4-B2 3 P4-B10 4 P4-B14 5 S4-5 6 WIRING NOTES 1. P4 is the Connector for the T “ ital Meter. It has two rows of 15 Pins each (Row A and Row B). Each Row connects to one aide of the Con- tact Board that extends out o the Digital Meter. Since the upper and lower Contacts are joined inside the Meter, Jumpers (1 thru 5) are used on Pins of the same number (i.e., P4-A14 and P4-B14) for redundancy. The P/N for P4 is 3VH15-1JN6, the FSCM is 05574 and the NSN 6936-00 -139-8928, 2. Al is the reference designationassigned to  Circuit Card   Assembly   70700-20687-041. 9. The last 2 digits of a wire number indicates the gauge of that wire. 4. Switch S4 Contact Pattern — Switch Position Contacts Made 1 (Keying Side) 1-2 and 4-5 Both (Center) 2-3 and 4-5 2  (Opposite  Key  Side) 2-3 and 5-6 4-20