5-7. Drip Pan Removal
c. Installation of Drip Pan.
When working on components located beneath the tank,
Install drip pan
you may find it convenient to remove the drip pan (74,
beneath tank using figure 4-9 and the following steps as
guides:
components.
(1) Line up all mounting holes of drip pan (74)
with mating holes in lower channel of tank support
WARNING
assembly (133).
A minimum of two men are required to tilt
the tank installation. Always block the
CAUTION
tank installation to prevent its falling.
Spacers (27, 40, and 71) are placed with
CAUTION
in tank support channel at each
Lift tank installation by handles, never by
attachment hole used for securing drip
booms or braces.
pan, tube flanges, and tube clamps to
a
Tilting Tank Installation. Carefully tilt the tank
tank support. When inserting bolts, be
installation backward unless it rests on the back frame of
sure bolt passes through spacers.
the tank support. Place blocking material of sufficient
Insert screw head from inside of tank
size and strength beneath the tank support frame to hold
support with washers and nuts on
tank installation in tilted position.
outside of tank support.
b. Removal of Drip Pan. Remove drip pan (74)
(2) Insert spacers (27, 40, and 71) within
from tank installation as follows, using figure 4-9 and the
channel and in line with mounting holes.
following steps as guides:
(3) Insert screws (26 and 39) from inside drip
(1) Remove lower nuts (24, 37, and 68),
pan, through the following components: lower channel of
washers (25, 38, and 69), screws (26, 39, and 70) and
tank support assembly (133); spacers (27 and 40); lower
spacers (27, 40, and 71) that secure drip pan to tank
holes in mounting flanges of liquid loading tube (41), and
support assembly (133).
pump inlet tube (28).
Secure
components
with
Note:
washers (25 and 38) and nuts (24 and 37).
Attaching hardware also secures bottom
(4) Insert screws (70), from inside drip pan,
portions of tube flanges of pump inlet tube
through the following components; lower channel of tank
(28), liquid loading tube (41), and tube lower
assembly (133); spacers (71), and lower tube clamp
clamps (73) to tank support assembly.
(73). Secure components with washers (69) and nuts
(2) Remove
drip
pan.
(68).
Section IV.
REMOVAL AND INSTALLATION OF MAJOR COMPONENTS
in position.
5-8. Pump and Brake Assembly
(c) Remove pump and brake assembly
a. Removal.
from pump support assembly.
(1) If synchromatic windmill assembly (24, fig.
(4) Remove elbow (15) from outlet port of
pump and brake assembly.
b. Installation.
Disconnect inlet and outlet hoses (13 and 14) from pump
(1) Attach pump and brake assembly (19) to
and brake assembly as instructed in paragraph 4-15.
pump support assembly (114) using figure 4-9 and the
(2) Disconnect brake cable assembly (11, fig.
following steps as guides:
(a) Loosen nuts (96) at top of pump
clevis pin (3). Disengage pump link (8) from brake
support assembly enough to permit slipping foot of pump
actuation lever of pump and brake assembly (19).
and brake assembly (19) over bushings (98).
Disconnect outlet hose (14) and inlet hose (13) from
(b) Slip upper slots in foot of pump and
pump and brake assembly.
brake assembly over bushings.
(3) Remove pump and brake assembly from
(c) Insert screws (18) through lower
pump support assembly (107) using figure 4-9 and the
holes in pump support assembly (107) and through slots
following steps as guides:
(a) Remove two bottom nuts (16),
in foot of pump and brake assembly. Place
washers
(17) and nuts (16) over screws.
washers (17), and screws (18).
(d) Secure all upper and lower nuts (96
(b) Loosen and back off two upper nuts
and 16).
(96) as required to permit slipping pump and brake
assembly from pump support assembly (107). Do not
remove nuts as they secure the pump support assembly
5-2
