TM 1-1510-218-10 3-56 NOTE There   are   some   SID   /   STAR   procedures that    are    not    suited    for    the    operational characteristics   of   the   KLN   90B.      These procedures are not included in the database. (1)   SID   and   STAR   procedures   are   stored with the airport for which they apply.  SID and STAR procedures are accessed through the APT 7 page.  If there  are  both  SID's  and  STAR's  for  a  given  airport, then  there  will  be  two  APT  7  pages,  one  to  select  a SID and the other to select a STAR.  This is indicated by APT+7. (2)   SID and STAR procedures are defined in three  parts:  the  name,  the  transition,  and  the  runway component.    The  APT  7  page  leads  the  pilot through the selection process. ay.  Selecting a SID. 1.   Select the departure airport APT 7 or ACT 7 page. 2.   Turn  the  right  cursor  on  by  pressing  the right  CRSR button.  Rotate the right outer knob  until  the  cursor  is  over  the  desired SID.  Press the ENT button. 3.   The  KLN  90B  will  now  ask  for  the  runway in   use.      Position   the   cursor   over   the appropriate   runway   and   press   the   ENT button. 4.   The transitions are presented for selection.        Move    the    cursor    over    the desired    transition    and    press    the    ENT button. 5.   The    KLN    90B    now   presents   a   list   of waypoints that make up the SID.  Review the waypoints.  Press the  ENT button with the cursor over LOAD IN FPL to load the SID into the active flight plan. 6.   The KLN 90B will add the SID procedure after   the   airport   reference   point   in   the active  flight  plan.    If  the  airport  reference point   is   not   included   in   the   active   flight plan,   the   KLN   90B   will   ask   to   add   this waypoint to the active flight plan. az.   Selecting   a   STAR.      The   steps   required   to select  a  STAR  are  very  similar  to  those  required  to select  a  SID.    The  only  difference  is  the  order  of  the steps   to   define   the   STAR   and   where   the   STAR   is loaded into the flight plan. 1.   Select  the  APT  7  or  the  ACT  7  page  for the destination airport.  Ensure the words, "SELECT  STAR"  are  displayed  near  the top of the screen. 2.   Turn  the  right  cursor  on  by  pressing  the right    CRSR    button    and,    if    necessary, rotate    the    right    outer    knob    until    the flashing cursor is over the desired STAR.   Press the ENT button. 3.   The KLN 90B will now ask which transition to use. 4.   In    some    cases,    the    STAR    procedure requires the selection of a specific runway.   To   select   a   specific   runway,   move   the cursor over the desired runway and press the ENT button. 5.   The   KLN   90B   now   presents   a   list   of waypoints     that     make     up     the     STAR.   Review these waypoints.   With the cursor over LOAD IN FPL, press the  ENT button to load the STAR into the active flight plan. The KLN 90B will then add the STAR procedure before  the  airport  reference  point  in  the  active  flight plan.    If  the  airport  reference  point  is  not  included   in the active flight plan, then the KLN 90B will ask to add this waypoint to the active flight plan. NOTE It  is  not  possible  to  load  a  SID  or  a  STAR into a flight plan other then FPL 0.  SID and STAR  procedures  are  deleted  from  FPL  0 after    the    power    is    off    for    more    than 5 minutes.  ba.  Editing  A  SID  Or  A  STAR.    SID  and  STAR procedures have procedure headers.  It is possible to use  these  headers  to  delete  and  change  the  entire procedure,   as   is   done   with   approach   procedures.   Refer to Figure 3-73.  Unlike approaches, it is possible to   add   and   delete   waypoints   in   SID   and   STAR procedures.